Necto Studio 6.01 doesn't work on MacOS

[dibor]

Hello.
After Installing new 6.01 version on Sanoma 14.3 - Necto doesn't run, application is starts and closed immediately after few seconds

Version 5 was works but 6 is doesn't

What to do?

Here Mac Studio with M1Max and latest MacOS Sanoma 14.3

Thank U.

[dibor]

Any answer from support?

[bobh]

Hi guys, Same problem here, I have a support ticket open and they are trying to figure out what the problem is, if you please supply whatever you can to help them find the problem.
For reference, here is my system info
intel I9
os: 14.3.1

also fails on a M1 mini mac
os:12 something

After complete uninstall and reinstalling program now starts but can't open a project or files

also tried newest version 6.01

[Dominic75]

Same here. Running on a M2. It sometimes works, but depending on the actions, it just crash. (Not really usuable)

[IvanJeremic]

Hi,

We are working on this issue, we are already speaking with Dibor on our help desk.

At the moment there is no solution since we are having a problem reproducing the issue on our MacOS systems (macOS BIG SUR version 11.7.10).

I will return to this forum when I get a solution to this issue.

Regards,

Ivan.

[Dominic75]

FYI -
I am running on Sonoma 14.4. When you enable Rosetta, the crash are less often - but the crash are replaced by non-functionning "click" instead. i.e without rosetta, when I click on modify a setup, the IDE crashes. When I enable Rosetta, clicking on modify a setup does nothing but does not crash. If you need some kind of logs just let me know.

Dominic

[IvanJeremic]

Hi,

Logs will be of help thank you.

If anyone has any more information (other OS that are showing a similar issue, steps taken for an issue to occur etc...) it will be of a lot of help.

Regards,

Ivan.

[Dominic75]

Hi Ivan, could you point me to which log you need? Not sure where Necto stores them.

Dominic

[IvanJeremic]

Hi,

We are still not able to reproduce this issue on our MAC devices.

Thank you all for your patience in this issue and sorry for the inconvenience.

Regards,

Ivan.

[spicacality@kelseymountain.org]

For what it's worth, I'm experiencing this issue as well. I'm running macOS Sonoma 14.3.1 on an M1 Pro processor. Necto starts fine and appears to work, but when I try to create a new "setup," it crashes immediately. The behavior has been very consistent so far.

Thanks for looking into it!

Peter

[IvanJeremic]

Hi,

Thank you all for your patience in all of this.

On the 2nd of April, there will be an update to Necto Studio.

This update should fix the issue with Necto Studio on MAC OS.

Sorry for the delay and regards,

Ivan.

[dibor]

Hello.
6.1 Necto do not solve the problem
Yes, application is runs, but crashed in every step while making new setup
I have fight 10 minutes for setting new setup without success, first time program crashed after choosing compiler, after that crashed after choosing board , third time after choosing MPU etc......

6.1_crash.png (43.83 KiB) Viewed 321 times

Guys, U are really amateur company!!!
I do not see any professionalism while last years

I have really spend money for very BAD ARM and AVR compilers and ugly IDE.
Really do not made any project by NECTO, only spend money
Did 6 project in the Bascom and CodevisionAVR without any problems

I think I need to forget this stupid NECTO project and do not come back to this compiler/IDE again.

Sorry and goodby.

[teckdev@gmail.com]

Try the update today on my mac. Still crashes all over the place. Crashes when trying to do a setup, crashes when opening an existing project, etc... . Sometimes is works, sometimes not. Also since I update to the latest version, CODEGRIP can't connect to the target anymore. I would not consider this release as fixes for MAC. In my case, I am worst then the version before.

Dominic

[IvanJeremic]

Hi,

Sorry to hear that the new realease did not fix the issue with MAC OS, can you send me your crash logs?

Regards,

Ivan.

[IvanJeremic]

Hi,

The CODEGRIP not connecting issue can be resolved by updating the CODEGRIP suite to 1.7.0 version and the firmware of the CODEGRIP programmer to 1.7.0.
https://download.mikroe.com/documents/f ... manual.pdf

Regards,

Ivan.