easypic v8 codegrip does not go on wifi
-
- Posts: 222
- Joined: 09 Apr 2011 11:08
- Location: ITALY / NAPOLI
easypic v8 codegrip does not go on wifi
hi to the forum, I have an easypic v8, and I am using mplab as ide, the problem that arose, and that mplab requires me the software codegrip 14.2 and firmware 14.1, now I update the firmware quietly, but I can no longer connect it wifi, the license is in my possession, and checking the update had canceled the license, logically I re-registered the wifi license, so I tried to reconnect with the wifi but again nothing, so please let me understand what not it goes that codegrip 14.1 does not allow wifi connection.
-
- Posts: 222
- Joined: 09 Apr 2011 11:08
- Location: ITALY / NAPOLI
Re: easypic v8 codegrip does not go on wifi
reloading codegrip I discovered that when I put the license, it gives me a message registrtion code already approved
Re: easypic v8 codegrip does not go on wifi
Hi,
Can you tell me which version of the CODEGRIP Suite are you using and the firmware version of the CODEGRIP programmer on the EasyPIC8 board ?
Regards,
Filip.
Can you tell me which version of the CODEGRIP Suite are you using and the firmware version of the CODEGRIP programmer on the EasyPIC8 board ?
Regards,
Filip.
-
- Posts: 222
- Joined: 09 Apr 2011 11:08
- Location: ITALY / NAPOLI
Re: easypic v8 codegrip does not go on wifi
hi flip, I upgraded the suite to 14.2 as required by the software, and the firmware instead is 14.1
Re: easypic v8 codegrip does not go on wifi
Hi,
Can you please check your WiFi parameters ?
Can you make a screenshot and paste them here ?
Regards,
Filip.
Can you please check your WiFi parameters ?
Can you make a screenshot and paste them here ?
Regards,
Filip.
-
- Posts: 222
- Joined: 09 Apr 2011 11:08
- Location: ITALY / NAPOLI
-
- Posts: 222
- Joined: 09 Apr 2011 11:08
- Location: ITALY / NAPOLI
Re: easypic v8 codegrip does not go on wifi
as you can see from the photos, the wifi license has disappeared, if I try to insert it it tells me that it has already been registered, while the wifi parameters does not accept them it always says operation failed.
if instead I install the 13.1 firmware together with the 13.1 software then it works a beauty, but I can't use it from mplab.
if instead I install the 13.1 firmware together with the 13.1 software then it works a beauty, but I can't use it from mplab.
Re: easypic v8 codegrip does not go on wifi
Hi,
Can you make a screenshot of the yellow envelope in the bottom right corner, when you click on it ?
Regards,
Filip.
Can you make a screenshot of the yellow envelope in the bottom right corner, when you click on it ?
Regards,
Filip.
-
- Posts: 222
- Joined: 09 Apr 2011 11:08
- Location: ITALY / NAPOLI
Re: easypic v8 codegrip does not go on wifi
Hi,
Please set the WiFI Mode and WiFi General settings according to the screenshots below (use your SSID and password, of course).
Regards,
Filip.
Please set the WiFI Mode and WiFi General settings according to the screenshots below (use your SSID and password, of course).
Regards,
Filip.
- Attachments
-
- 22.png (60.72 KiB) Viewed 2823 times
-
- 11.png (60.64 KiB) Viewed 2823 times
-
- Posts: 222
- Joined: 09 Apr 2011 11:08
- Location: ITALY / NAPOLI
Re: easypic v8 codegrip does not go on wifi
immagini gif tumblr
hi flip thanks for the availability, but as you can see the problem persists, I have the vague doubt that when you update the codegrip firmware, the associated wifi license is deleted, and being that the license I use is already registered then it requires a new license, this it's just my guess, but reading on the forum I found a similar case that was solved by entering the wifi license code.
so it's not that maybe when we update the firmware then a licensing problem is generated?
Re: easypic v8 codegrip does not go on wifi
Hi,
Can you please open a ticket on the HelpDesk regarding this issue ?
Regards,
Filip.
Can you please open a ticket on the HelpDesk regarding this issue ?
Regards,
Filip.
-
- Posts: 222
- Joined: 09 Apr 2011 11:08
- Location: ITALY / NAPOLI
Re: easypic v8 codegrip does not go on wifi
sorry flip, could you give me more precise information, helpdesk things, how do i open a ticket?
Re: easypic v8 codegrip does not go on wifi
Hi,
You can simply write an e-mail to support att mikroe dot com.
Regards,
Filip.
You can simply write an e-mail to support att mikroe dot com.
Regards,
Filip.