hi i have programmed a 24f32ga004 with the usb programmer i received with the
lv24-33 development kit this is using icsp, but i cannot get the 24f16ka102 to program i get messages like this "device currently selected is not {lvpicflasdh prog} driver is usb18f firmware v1.20 with latest updated version basic compiler 5.7.0.0
can't program pic24f16ka102 using lv24-33 usb programmer
-
- Posts: 5
- Joined: 25 Jun 2012 09:37
- dejan.odabasic
- mikroElektronika team
- Posts: 2649
- Joined: 30 Apr 2012 14:20
Re: can't program pic24f16ka102 using lv24-33 usb programmer
Hello,
could you please tell me which programming application are you using?
If you are not using mikroProg Suite I strongly suggest that you try programing using mikroProg Suite.
Did you updated to PRO version of mikroBasic compiler?
Best regards.
could you please tell me which programming application are you using?
If you are not using mikroProg Suite I strongly suggest that you try programing using mikroProg Suite.
Did you updated to PRO version of mikroBasic compiler?
Best regards.
-
- Posts: 5
- Joined: 25 Jun 2012 09:37
Re: can't program pic24f16ka102 using lv24-33 usb programmer
yes mikroBasic PROfor dsPIC v5.7.0 also why do you have 2 rows of the
same pinout on the usb in system programmer with icd.
mcu vcc - board vcc
mcu rb6 - rb6
mcu rb7 - rb7
mcumclr - mclr
gnd - gnd
same pinout on the usb in system programmer with icd.
mcu vcc - board vcc
mcu rb6 - rb6
mcu rb7 - rb7
mcumclr - mclr
gnd - gnd
- dejan.odabasic
- mikroElektronika team
- Posts: 2649
- Joined: 30 Apr 2012 14:20
Re: can't program pic24f16ka102 using lv24-33 usb programmer
Hello,
you didn't answered me which application are you using for programing.
Are you using mikroProg Suite 2.25?
Please take a look at our mikroProg user manual: http://www.mikroe.com/eng/downloads/get ... l_v220.pdf
Section 8. Multiplexer.
Best regards.
you didn't answered me which application are you using for programing.
Are you using mikroProg Suite 2.25?
Doubled lines are used for multiplexer which allows the usage of programming pins as I/O lines when not in programming/debugging mode.denisbeeby wrote:...why do you have 2 rows of the same pinout on the usb in system programmer with icd.
Please take a look at our mikroProg user manual: http://www.mikroe.com/eng/downloads/get ... l_v220.pdf
Section 8. Multiplexer.
Best regards.
-
- Posts: 5
- Joined: 25 Jun 2012 09:37
Re: can't program pic24f16ka102 using lv24-33 usb programmer
yes i am using mikroProgSuite 2.25
- dejan.odabasic
- mikroElektronika team
- Posts: 2649
- Joined: 30 Apr 2012 14:20
Re: can't program pic24f16ka102 using lv24-33 usb programmer
Hello,
I have tried to replicate error that you explained but didn't succeed.
Could you please send the photos of your hardware/software setup and error report that you get.
Best regards.
I have tried to replicate error that you explained but didn't succeed.
Could you please send the photos of your hardware/software setup and error report that you get.
Best regards.
-
- Posts: 5
- Joined: 25 Jun 2012 09:37
Re: can't program pic24f16ka102 using lv24-33 usb programmer
it works when i use the real ice and mplab then i have no problems ,my mikroelektronika
usb programmer works when i use the pic16ga004 the error says not a lvflash device.
does it matter which row on the usb programmer i use to connect the target device to ?
usb programmer works when i use the pic16ga004 the error says not a lvflash device.
does it matter which row on the usb programmer i use to connect the target device to ?
- dejan.odabasic
- mikroElektronika team
- Posts: 2649
- Joined: 30 Apr 2012 14:20
Re: can't program pic24f16ka102 using lv24-33 usb programmer
Hello,
You need to use row on the knob side of the connector (odd pins of the connector).
Please take a look at mikroProg user manual (6. IDC10 Pinout):
http://www.mikroe.com/eng/products/view ... and-pic32/
I have tested the programing of PIC24F16ka102 with mikroProg and everything was in order.
That's why I asked you to send me a photo of your hardware connection.
Best regards.
You need to use row on the knob side of the connector (odd pins of the connector).
Please take a look at mikroProg user manual (6. IDC10 Pinout):
http://www.mikroe.com/eng/products/view ... and-pic32/
I have tested the programing of PIC24F16ka102 with mikroProg and everything was in order.
That's why I asked you to send me a photo of your hardware connection.
Best regards.
-
- Posts: 5
- Joined: 25 Jun 2012 09:37
Re: can't program pic24f16ka102 using lv24-33 usb programmer
HI I WILL BRING MY CAMERA IN TOMMORROW AND TAKE A PIC OR TWO
THE MESSAGE I GET IN MIKROPROGSUITE BELOW THE CONFIG STUFF UNDER
TYPE = UNKNOWN IT DOES NOT RECOGNISE THE PIC I HAVE LOOKED AT YOUR SUGGESTED MANUALS AND HAVE CONNECTED THE LV24-33 CORRECTLY MY VOLTAGE IS 3.3V ON THE PIC I HAVE DECOUPLING CAPS. RUNNING PIC AT 16MHZ. 10K BETWEEN +VCC AND MCLR
REGARDS
DENIS
THE MESSAGE I GET IN MIKROPROGSUITE BELOW THE CONFIG STUFF UNDER
TYPE = UNKNOWN IT DOES NOT RECOGNISE THE PIC I HAVE LOOKED AT YOUR SUGGESTED MANUALS AND HAVE CONNECTED THE LV24-33 CORRECTLY MY VOLTAGE IS 3.3V ON THE PIC I HAVE DECOUPLING CAPS. RUNNING PIC AT 16MHZ. 10K BETWEEN +VCC AND MCLR
REGARDS
DENIS