Hello,
I ordered your SpeakUp Click and Pi because I saw the video RPI + XBMC + Pi + click Speakup. and i want to use the internet by voice to help disabled people in both hands using the internet so they can browsing, use facebook and so on.
My question is should i use standalone mode or click mode and what's the difference between them and after give comments to speakup and connect it to PI do i need coding in order my commends be working such as if i said Google it will open directly or i need coding for doing that .
Thank you
Need a help
- stefan.filipovic
- mikroElektronika team
- Posts: 1135
- Joined: 18 Dec 2018 10:30
Re: Need a help
Hi,
It depends on which way you want to use this click board.
In standalone mode: Onboard MCU directly controls external devices using 12 user-programmable GPIOs.
In click mode: Sends index of the matched voice command to a selectable interface: USB or UART
When a new command is recorded, you need to set its action. The action will be performed when the voice command is recognized. Also, a 16-bit index number of the voice command will be sent via the chosen communication interface (UART or USB).
In your case, there must be some additional code for RPi that will do the job based on this action.
I suggest you read the following user manual carefully:
https://download.mikroe.com/documents/a ... v100-a.pdf
Kind regards,
It depends on which way you want to use this click board.
In standalone mode: Onboard MCU directly controls external devices using 12 user-programmable GPIOs.
In click mode: Sends index of the matched voice command to a selectable interface: USB or UART
When a new command is recorded, you need to set its action. The action will be performed when the voice command is recognized. Also, a 16-bit index number of the voice command will be sent via the chosen communication interface (UART or USB).
In your case, there must be some additional code for RPi that will do the job based on this action.
I suggest you read the following user manual carefully:
https://download.mikroe.com/documents/a ... v100-a.pdf
Kind regards,
Stefan Filipović
-
- Posts: 2
- Joined: 04 Sep 2019 20:44
Re: Need a help
Hello,
I also ordered your SpeakUp click and try some tests but i have a issue with the notify a master.
I try to get index of command on USB or UART interface but nothing worked.
The SpeakUp recognizes my command but nothing goes out on the interface.
I known that my wired is correct because i get "READY" message at startup with UART output but nothing more.
Do you have any idea of what is wrong ?
Regards,
Benoit
I also ordered your SpeakUp click and try some tests but i have a issue with the notify a master.
I try to get index of command on USB or UART interface but nothing worked.
The SpeakUp recognizes my command but nothing goes out on the interface.
I known that my wired is correct because i get "READY" message at startup with UART output but nothing more.
Do you have any idea of what is wrong ?
Regards,
Benoit
- stefan.filipovic
- mikroElektronika team
- Posts: 1135
- Joined: 18 Dec 2018 10:30
Re: Need a help
Hi Benoit,
I apologize for the late reply.
Please make sure to configure UART Terminal to display data in a decimal data format.
If you use the USART Terminal tool from our compilers, just select the DEC radio button for Data Format.
Kind regards,
I apologize for the late reply.
Please make sure to configure UART Terminal to display data in a decimal data format.
If you use the USART Terminal tool from our compilers, just select the DEC radio button for Data Format.
Kind regards,
Stefan Filipović
-
- Posts: 1
- Joined: 25 Aug 2021 13:05
Re: Need a help
I am quite disappointed with the performance in speech recognition... Where is the XBMC project?
- filip.grujcic
- Posts: 822
- Joined: 14 May 2018 08:34
Re: Need a help
Hello,
Unfortunately, that project is not available anymore. I apologize for the inconvenience.
Kind regards,
Unfortunately, that project is not available anymore. I apologize for the inconvenience.
Kind regards,
Filip Grujcic