I have some problem in the IDE graphical aspects.
1) Attached you can find three pictures of the problem. It is not a big problem, but sometimes there is no way to read some informations shown in
the below bars.
2) In hardware/software debug mode, i did not find a way to move the program counter (or software context) in the debug windows.
3) I did not find a reset button anywhere.
Does anybody have this information?
Thank you
MikroBasic IDE
-
- Posts: 101
- Joined: 04 Nov 2016 13:09
MikroBasic IDE
- Attachments
-
- IMG_3.PNG (3.23 KiB) Viewed 2874 times
-
- IMG_2.PNG (4.29 KiB) Viewed 2874 times
-
- IMG_1.PNG (5.31 KiB) Viewed 2874 times
- lana.arsic
- mikroElektronika team
- Posts: 1715
- Joined: 15 Jan 2016 12:50
Re: MikroBasic IDE
Hi Alessandro Fulignani,
Welcome to the MikroE forum.
1) Can you tell me which version of the compiler are you using?
Can you send me screenshot of the whole screen?
2) Unfortunately, Stopwatch Window you can only put in Software debugger,
not in Hardware debugger.
3) There is Reset To Zero button in the Stopwatch Window.
Best regards,
Lana
Welcome to the MikroE forum.
1) Can you tell me which version of the compiler are you using?
Can you send me screenshot of the whole screen?
2) Unfortunately, Stopwatch Window you can only put in Software debugger,
not in Hardware debugger.
3) There is Reset To Zero button in the Stopwatch Window.
Best regards,
Lana
-
- Posts: 101
- Joined: 04 Nov 2016 13:09
Re: MikroBasic IDE
Hi Lana,
Thank you for your help.
I bought MikroBsic PRO for ARM V 4.9.0 ( licensed to my company). Running on W10( updated to the last upgrade pack)
Attached you can see the full screen pictures. There, you can see that all the bottom bar are half hidden.
The same problem is also present in the MikroProg windows, the "Progress bar" it's half hidden.
I want to add a new question about the debug phase. In Code window it seem that it work only with standard parameter.
If i try to change the parameter on the right, in Address scope, the windows gone stuck, and i get an error message.
If i try to change the parameter on the left, nothing happen. No refresh, no download, no actions.
Do you know when it is planned the next MikroBasic PRO release?
Thank you,
Alessandro
Thank you for your help.
I bought MikroBsic PRO for ARM V 4.9.0 ( licensed to my company). Running on W10( updated to the last upgrade pack)
Attached you can see the full screen pictures. There, you can see that all the bottom bar are half hidden.
The same problem is also present in the MikroProg windows, the "Progress bar" it's half hidden.
I want to add a new question about the debug phase. In Code window it seem that it work only with standard parameter.
If i try to change the parameter on the right, in Address scope, the windows gone stuck, and i get an error message.
If i try to change the parameter on the left, nothing happen. No refresh, no download, no actions.
Do you know when it is planned the next MikroBasic PRO release?
Thank you,
Alessandro
- Attachments
-
- Cattura.PNG (228.58 KiB) Viewed 2838 times
-
- Posts: 101
- Joined: 04 Nov 2016 13:09
Re: MikroBasic IDE
Hi again Lana,
I forget to add that the control button "Minimize" on the main windows, does not work.
Thank you,
Alex
I forget to add that the control button "Minimize" on the main windows, does not work.
Thank you,
Alex